- Updated changes.md
- Updated Release Notes

- Updated .vveh file format and Vehicle Editor

- Renamed output "FC" to "FC-Map" for better clarification
- Same header for g/h and g/km output
- Reduced minimum turbine speed for 1C-to-2C AT up-shift condition from 900 to 700rpm.

- updated version number

- Added V2.1 Release Notes
- Updated Changelog and User Manual
- Updated version to 2.1

* Bugfix: VECTO freezed if torque converter creeping was not possible due to low full load torque. Now it will abort with error message.
* Bugfix: Small fixes in torque converter model

* Various bugfixes in AT model
* rdyn validation
* Fixed bug in map interpolation

* Warning when opening or running files if file was created in different mode (Declaration/Engineering Mode)
* New Decl./Eng. Mode switch
* Small fixes

* Updated cDeclaration and Segment Table to deal with multiple VCDV files for each class (depending on Long Haul with or w/o Trailer)
* Expanded transmission loss maps of generic vehicles to prevent extrapolation errors

* AT/TC Update
+ Various smaller fixes

* Use Markdown and Rename VECTO Changelog.txt-->CHANGES.md

* Updated CSV file format. Now only one header with units included.
* Changed input file comment symbol form "c" to "#".
* Replaced old Demo/Default Data with "Demo Vehicles"
* Updated User Manual

* Mission profiles are shown in VECTO Editor in Declaration Mode
* Removed "Extrapolation not possible!" exceptions in cDelaunayMap for faster debugging
* Better Cd * A handling in GUI and input file

* Removed rated power (not used anymore)
* Removed rated engine speed form engine file. Now calculated form vfld file.

* Target deceleration (.vacc file) doesn't work right if distance-steps in driving cycle are too large. Now limited to 1[m].
* Bugfix: When moving job files up or down in job list the "checked jobs" counter was incorrectly reduced.
* Bugfix: Vehicle Editor: "New file" had invalid axle configuration (caused crash when trying to edit).

* Bugfix: Eco Roll didn't go into motoring operation when Overspeed-Limit was reached (could cause higher FC than Overspeed Mode)
* Minor update in demo data (12t motoring curve)
* Cleared up Demo Data
* Small fix in User Manual

- Exact road gradient calculation (see changelog)

- Bugfix: Gears using torque converter and transmission loss maps may cause invalid "out of engine operation range" errors
- Null values for FzISO will abort calculation

* Use '*' char for lists.

- Update Notes updated (still open: File Signing)
- Load-dependent RRC finished

- Files can be converted in JSON format. Backup will be created.
- Option in Settings whether to use JSON format or not
- Finished load-dependent RRC

-small changes in User Manual
-update in .vecto JSON input: Parameters not needed in Engine Only are now optional

- "zero" stop-times are no longer allowing in distance-based cycles
- bugfix: Stand-still at cycle end (distance-based) was ignored
- bugfix: Crashes when distance correction at end of cycle
- added default cycles to repo (TODO: default input files)
- added Update Notes to repo

- When speed is under 5km/h and engine in motoring operating then gearbox shifts to Neutral
- "Minimum (actual) speed" instead of "Min. Target Speed" (Eco-Roll, Overspeed, Look Ahead Coasting)

- <DRAG> keyword in Engine Only mode enabled
- variable gear number / TC possible in multiple gears
- transmission loss approximation for PreRun and Gear Shift Model

- Torque Converter updates ....still in development

- Same job file list for BATCH and STANDARD
- FC extrapolation will not abort calculation. Invalid FC values are marked in output as "ERROR".
- Bugfix: FC interpolation failed when load points matched map points exactly.
- Bugfix: Invalid "FC= -10000!" errors when outside of FC-Map
- Updates in torque converter IN DEVELOPMENT
- No abortion if transmission output and input torque have different signs (In>0, Out<0)
- Updated modal results header
- New parameters in modal results (see changelog)
- Bugfix: Error if Look-Ahead Coasting was disabled.
- Eco-Roll revised (see changelog)
- Removed "IgnoreFCextrapol" form DEV-Options

- Fixed error in power calculation (rotatory part of acceleration force)
- Updated changelog.html

- Changed "Retarder" to "Retarder Losses" in Vehicle Editor to avoid misunderstandings

- Fixed assembly information
- Removed duplicate icon form User Manual
- updated readme.txt

- Updated Quick Start Guide
- New Welcome Dialog
- Updated Demo Data
- Update Notes and Support links in Help Menu of Mainform

- Added PicCoordLogger.exe (for User Manual development)
- Updated Tabindices for F_GEN controls
- Disabled distance correction for coasting to avoid engine leaving coasting operation