- Updated .vveh file format and Vehicle Editor

- Updated .vgbx file format
- Updated .veng file format
- Removed WHTC Correction Factor Calculation

- Renamed output "FC" to "FC-Map" for better clarification
- Same header for g/h and g/km output
- Reduced minimum turbine speed for 1C-to-2C AT up-shift condition from 900 to 700rpm.

- Small update in TC model

- updated version number

- Added V2.1 Release Notes
- Updated Changelog and User Manual
- Updated version to 2.1

- "DEV" tab is now "Test" tab

- Added AT Bus to Generic Vehicles
- Shift model updated

* DEV Tab permanently enabled!
* TClimit in DEV tab
* Removed unused DEV parameters

* Errors if full load curve is too "short"
* Transmission loss extrapolation Errors are now Warnings in Engineering Mode.

- Bugfix: VECTO didn't check if the full load curve covers the range up to nhi. Now it will abort if the full load curve is "too short"
- Update in Torque Convert model: Allowed engine speed range up to n95h (before: Pmax-speed)

- Bugfix: Error in engine inertia power calculation
- Torque Converter losses in modal results

* Bugfix: VECTO freezed if torque converter creeping was not possible due to low full load torque. Now it will abort with error message.
* Bugfix: Small fixes in torque converter model

* Various bugfixes in AT model
* rdyn validation
* Fixed bug in map interpolation

* Added Developer Guide (including picture source)

* Implemented engine-side TC inertia input parameter in GBX file
* Updated User Manual for TC inertia
* Relabeled "OK" buttons to "Save" in input file editors

* Fixed small TC issue

* AT/TC Update
+ Various smaller fixes

* Updated .vsum(.json)
** Added l/100km and CO2 results. (Fixed VECTO-33)
** Added FC-Final.
** Added Loading. (json)
** Added missing fuel parameters. (json)
* Updated README.md

* Updated Segment Table header
* Fixed Eco Roll (VECTO-30)
* Fixed Cycles in VECTO Editor being overwritten in Engineering Mode (VECTO-31)

readme: Update Release-checklist
BUG: Minor, sample Coach-file fails: Generic Vehicles\Engineering Mode\24t Coach\24t Coach.vecto

* Updated CSV file format. Now only one header with units included.
* Changed input file comment symbol form "c" to "#".
* Replaced old Demo/Default Data with "Demo Vehicles"
* Updated User Manual

* Removed pre-header from .vmod and .vsum files
* Updated Graph  for new .vmod format

* Mission profiles are shown in VECTO Editor in Declaration Mode
* Removed "Extrapolation not possible!" exceptions in cDelaunayMap for faster debugging
* Better Cd * A handling in GUI and input file

* Added EUPL headers to new source files
* Updated Declaration folder
* Moved GUI/report source files to new folder (outside Declaration folder)
* Fixed opening .vmod files in Graph from Message list

* Added pdf report output
* Added charts in files editors
* Added declaration mode features
* Removed GRAPHi calls
* Added visualizer for modal results (replaces GRAPHi)(open)
* Changes cConfig format to JSON
* Cleaned up code

* Removed rated power (not used anymore)
* Removed rated engine speed form engine file. Now calculated form vfld file.

* Bugfix: Eco Roll didn't go into motoring operation when Overspeed-Limit was reached (could cause higher FC than Overspeed Mode)
* Minor update in demo data (12t motoring curve)
* Cleared up Demo Data
* Small fix in User Manual

* Add LICENSE.txt file.
* Add lic-header in all .vb files.
* Add python script for adding lic-headers.
* Add lic-header also in a powershell-script.

- Speed reduction in smaller steps to get closer to full load curve (before speed was sometimes reduced too much and caused problem with gear shifting)
- Updates in demo data